Tightening Torques
Lines beginning with * are TORQUE WRENCH SETTINGS, REVISED: 12/96

* GENERAL
* Bolt M6 10 Nm
* Bolt M8 25 Nm
* Bolt M10 45 Nm
* Bolt M12 80 Nm
* 1/4 UNC/UNF 9 Nm
* 5/16 UNC/UNF 25 Nm
* 3/8 UNC/UNF 40 Nm
* 7/16 UNC/UNF 75 Nm
* 1/2 UNC/UNF 90 Nm
* 5/8 UNC/UNF 135 Nm

ENGINE
Cylinder head nuts 50 lb ft (7.0 kg m) size 9/16"
 Additional nut & bolt (1275 GT) 25 lb ft (3.5 kg m)
 Emission control engines 40 lb ft (5.5 kg m)
Rocker pedestal nuts 24 lb ft (3.2 kg m)
Rocker cover 3.5 lb ft (0.5 kg m)
Manifold to cylinder head 14 lb ft (1.9 kg m) size 1/2"
Heater control to cyl head 8 lb ft (1.1 kg m)
Water outlet elbow 8 lb ft (1.1 kg m) size 7/16"
Temperature sender unit 16 lb ft (2.2 kg m)
Spark plugs 18 lb ft (2.5 kg m)
Main bearing cap bolts  63 lb ft (8.7 kg m)
Connecting rod big end cap:
 Bolts 37 lb ft (5.1 kg m)
 Nuts (1275 GT) 33 lb ft (4.6 kg m)
Piston pin clamp bolts (848 cc) 24 lb ft (3.2 kg m)
Camshaft nut 65 lb ft (8.9 kg m) size 1 1/4"
Crankshaft pulley nut 75 lb ft (10.3 kg m) size 1 1/4"
Timing cover and front plate:
1/4 in LTNF bolts 5 lb ft (0.7 kg m)
5/16 in LTNF bolts 12 lb ft (1.7 kg M)
Water pump 16 lb ft (2.2 kg m)
Cylinder side covers 3.5 lb ft (0.5 kg m)
Clutch cover to pressure plate (driving pins) 16 lb ft (2.2 kg m)
Drive strap to flywheel 16 lb ft (2.2 kg m)
Flywheel centre bolt 112 lb ft (15.5 kg m) size: (pre-verto)   1.5" , (verto)  30mm (thread = 5/8-16. Dit zou UN moeten zijn (Dus geen UNF of UNC) )
Flywheel housing bolts & stud nuts 18 lb ft (2.5 kg m)
Oil pump 8 lb ft (1 -1 kg m)
Oil pipe banjo 38 lb ft (5.3 kg m)
Oil filter head nuts  14 lb ft (1.9 kg m)
Oil filter bowl centre bolt  14 lb ft (1.9 kg m)
Oil filter head nuts 14 lb ft (1.9 kg m)
Oil pressure relief valve - dome nut 43 lb ft (5.9 kg m)

* ENGINE
* Timing gear cover bolts 16 Nm
* Timing gear nuts 90 Nm
* Timing chain tensioner bolts 22 Nm
* Cylinder head nuts 34 Nm then a further 34 Nm
* Front cover plate bolts 11 Nm
* Rocker shaft nuts 25 Nm
* Camshaft thrust plate screws 11 Nm
* Rocker cover bolts 5 Nm
* Crankshaft pulley bolt 150 Nm
* Engine LH mounting:
* Mounting to subframe - nuts 25 Nm
* Mounting to engine - bolts 25 Nm
* Engine RH mounting:
* Mounting to flywheel housing cover - bolts 18 Nm
* Mounting to subframe - nuts 22 Nm
* Engine steady bar upper bolts 22 Nm
* Engine steady bar lower:
* Bar to subframe bolt 40 Nm
* Bar to flywheel housing bolt 40 Nm
* Oil pressure gauge sensor 60 Nm
* Oil pressure relief valve cap 60 Nm
* Oil pressure switch 25 Nm
* Oil pump to engine - bolts 11 Nm
* Flywheel housing to engine/gearbox - bolts 25 Nm
* Earth lead to engine - bolt 10 Nm
* Engine to gearbox - nuts and bolts 8 Nm
* Flywheel to crankshaft - bolt 150 Nm
* Flywheel housing cover - bolts 10 Nm
* Engine mounting adaptor plate to engine - bolts 25 Nm

* EMISSION CONTROL
* Oil breather/separator to flywheel housing 18 Nm
* Catalytic converter to tail pipe nuts 9 Nm
* Catalytic converter to front pipe nuts 45 Nm
* Emission canister purge valve to body - bolts 9 Nm

* ENGINE MANAGEMENT SYSTEM
* ECT sensor to thermostat housing 15 Nm
* MAP sensor to inlet manifold 6 Nm
* IAT sensor to inlet manifold 7 Nm
* TP sensor to throttle body screws 1.5 Nm
* Throttle housing to inlet mainifold - bolts 8 Nm
* Throttle pedal nuts 25 Nm
* Spark plugs 25 Nm
* Ignition coil to bracket - bolts 10 Nm
* HO2S to exhaust manifold 55 Nm
* Air cleaner to inlet manifold 7 Nm
* ECM to mounting bracket 10 Nm
* ECM mounting bracket to body 10 Nm
* IACV to inlet manifold - bolts 7 Nm
* CMP sensor to engine - bolt 10 Nm
* CKP sensor to flywheel housing - bolts 6 Nm
* CKP sensor multiplug to flywheel housing - bolt 3 Nm

* FUEL SYSTEM
* Fuel breather valve nut 9 Nm
* Fuel pump to fuel tank nuts 9 Nm
* IFS to bulkhead - screws 2 Nm
* Fuel filter mounting bracket to body 9 Nm
* Fuel pipe unions to fuel filter 30 Nm
* Fuel feed/return pipes to fuel rail 5 Nm
* Fuel rail to inlet manifold - bolts 10 Nm

* COOLING
* Radiator brackets to bonnet platform 9 Nm
* Thermostat housing bolts 11 Nm
* Coolant pump bolts 22 Nm
* Coolant pump pulley bolts 10 Nm
* Expansion tank to mounting bracket 10 Nm
* Expansion tank mounting bracket to body 10 Nm

* MANIFOLD AND EXHAUST
* Front pipe to manifold nuts 22 Nm
* Front pipe to differential housing 22 Nm
* Inlet and exhaust manifold nuts 22 Nm
* Catalytic converter to tail pipe nuts 9 Nm
* Catalytic converter to front pipe nuts 45 Nm

* CLUTCH
* Flywheel centre bolt 150 Nm
* Pressure plate to flywheel bolts 25 Nm
* Flywheel housing to engine block bolts 25 Nm
* Slave cylinder to mounting bracket 37 Nm
* Slave cylinder mounting bracket to flywheel housing:
* M8 bolts 37 Nm
* M5 bolt 7 Nm .
* Pipe union to master cylinder 14 Nm
* Pipe union to slave cylinder 14 Nm

MANUAL TRANSMISSION
Drain plug 25 lb ft (1.1 kg m)
Transmission case to crankcase 6 lb ft (0.8 kg m)
Transmission case studs:
 3/8 UNC 8 lb ft (1.1 kg m)
 5/16 UNC 6 lb ft (0.8 kg m)
Transmission case stud units:
 3/8 in UNF 25 lb ft (3.5 kg m)
 5/16 in UNF 18 lb ft (2.5 kg m)
Gearchange extension bottom cover plate 6 lb ft (0.8 kg m)
input shaft nut 150 lb ft (20.7 kg m)
Mainshaft nut 150 lb ft (20.7 kg m)
Crownwheel to differential case 60 lb ft (8.3 kg m)
Final drive housing end cover bolts 18 lb ft ( 2.5 kg m)
Drive flange to final drive shaft nuts 70 lb ft (9.6 kg m)
Speedometer drive housing nuts 18 lb ft (2.5 kg m)

* MANUAL GEARBOX
* Gearbox to engine bolts 28 Nm
* Third motion shaft bearing retaining bolts 18 Nm
* First motion shaft gear nut 200 Nm
* Speedometer drive housing to gearbox - bolts 25 Nm
* Speedometer drive housing cover - bolts 8 Nm
* Speedometer drive pinion clamping plate - bolt 8 Nm

AUTOMATIC TRANSMISSION
Converter centre bolt 112 lb ft (15.5 kg m)
Converter, six central bolts 21 lb ft (2.9 kg m)
Converter drain plugs 20 lb ft (2.8 kg m)
Converter housing bolts 18 lb ft (2.5 kg m)
Transmission case to crankcase nut 12 lb ft (1.7 kg m)
Input shaft nut 70 lb ft (9.7 kg m)
Kickdown control assembly to trans. casing (on nylon housing) 5 lb ft (0.7 kg m)
Drive flange to find drive shaft bolts 43 lb ft (5.9 kg m)
Oil filter bowl 14 lb ft (1.9 kg m)

FRONT SUBFRAME
Later than 1976 Tower bolts 49 lb ft (67 Nm) 1 5/16" (thread 3/4" UNF)

FRONT SUSPENSION
Drive shaft nut (front hub):
 Drum front brakes 60 lb ft (8.3 kg m) size  15/16"  ???
 Disc front brakes (1275 GT) 150 lb ft (20.7 kg m) size 1.5"
Swivel hub ball joint nuts 38 lb ft (5.3 kg m) size 1.5"
Swivel joint ball pin retainer 75 lb ft (10.3 kg m) size 11/16"
Steering arm to swivel hub 35 lb ft (4.8 kg m)
Upper suspension arm pivot shaft nuts 53 lb ft (7.3 kg m)
Lower suspension arm pivot shaft nuts 33 lb ft (4.5 kg m)
Tie-rod to lower arm 19 lb ft (2.6 kg m)
Tie-rod to body bracket 22 lb ft (3.0 kg m)
Drive shaft coupling 'U' bolt nuts 10 lb ft (1.4 kg m)
Road wheel nuts 45 lb ft (6.4 kg m) size (imperial)   11/16" ,  (metric)  17mm   (usually); thread 3/8" unf

REAR SUSPENSION
Hub nut 60 lb ft (8.3 kg m) size 15/16"     ???
Radius arm pivot shaft nuts 53 lb ft (7.3 kg m)

* SUSPENSION
* Wheel nuts:
* Alloy wheels 50 Nm
* Steel wheels 60 Nm
* Upper arm to front hub 52 Nm
* Lower arm to front hub 52 Nm
* Front hub to drive shaft - nut 260 Nm
* Front subframe turret bolts 67 Nm - 1 5/16" 
* Front damper to body bracket - nut 37 Nm
* Front damper to upper arm - nut 48 Nm
* Front subframe to body - nuts and bolts 25 Nm
* Rear damper to body 25 Nm
* Rear damper to suspension arm 25 Nm

STEERING
Track rod to steering arm 22 lb ft (3.0 kg m)
Steering arm to swivel hub 33 lb ft (4.5 kg m)
Steering rack 'U' bolts 11 lb ft (1.5 kg m)
Steering column to pinion shaft clamp bolt 12 lb ft (1.7 kg m)
Steering column upper support bracket 14 lb ft (1.9 kg m)
Steering wheel retaining nut 35 lb ft (4.8 kg m) size 1.5"   (alternatively: 33 mm =1 5/16" )

* STEERING
* Steering wheel nut 49 Nm
* Drivers air bag module Torx screws 9 Nm
* Steering column upper mounting to fascia rail bolt 25 Nm
* Inner column to steering rack pinion clamp bolt 16 Nm
* Track rod ball joint to steering arm nut 30 Nm
* Steering rack U-bolts 15 Nm
* Steering rack pinion cover bolts 15 Nm
* Steering arm to front hub bolts 45 Nm
* Steering column to pinion - bolt 15 Nm

 BRAKES
Calliper retaining bolts 38 lb ft (5.3 kg m)
 Brake disc to driving flange 42 lb ft (5.8 kg m)
 Rear backplate to radius arm 20 lb ft (2.8 kg m)
Split braking system: Tandem master cyl. reservoir flange screws 5 lb ft (0.7 kg m)
Master cylinder body outlet connections 28 lb ft (3.9 kg m)
Inbuilt PDWA end plug 33 lb ft (4.5 kg m)
PDWA end plug 26 lb ft (3.6 kg m)
Nylon switch to PDWA 14 lb ft (1.9 kg m)
Inertia valve end plug 45 lb ft (6.4 kg m)

* BRAKES
* Bleed screw to caliper 9 Nm
* Brake master cylinder nuts 25 Nm
* Brake servo banjo bolt 50 Nm
* Brake servo to bracket nuts 25 Nm
* Brake servo bracket nuts and bolts to body 25 Nm
* Brake caliper to swivel hub bolts 52 Nm
* Brake disc to drive flange bolts 57 Nm
* Brake drum back plate to radius arm bolts 28 Nm
* Pressure limiting valve to body bolt 17 Nm
* Brake pipe to master cylinder - union 14 Nm
* Brake drum to hub - screw 7 Nm
* Brake pipe union to pressure reducing valve 14 Nm
* Pressure reducing valve to body - bolt 17 Nm
* Brake pedal pivot bolt - nut 15 Nm
* Brake light switch bracket to pedal box 5 Nm
* Brake hose union to caliper 15 Nm
* Brake pipe unon to wheel cylinder 14 Nm

ELECTRICAL EQUIPMENT
Dynamo pulley nut 16 lb ft (2.2 kg m)
Dynamo mounting bolts 17 lb ft (2.3 kg m)
Dynamo mounting bracket 25 lb ft (3.5 kg m)
11 AC Alternator:
 Through bolts 50 lb in (0.57 kg m)
 Brush box fixing screws 10 lb in (0.12 kg m)
16 ACR Alternator:
 Pulley nut 28 lb ft (3.9 kg m)
Starter motor mounting bolts 25 lb ft (3.5 kg m)
Distributor, plate retaining screws 8 lb ft (1.1 kg m)
Distributor clamp bolt:
 Fixed nut type 50 lb in (0.58 kg M)
 Fixed bolt type 30 lb in (0.35 kg m)

* ELECTRICAL
* Alternator pulley nut 25 Nm
* Auxiliary drive belt tensioner pulley nut 25 Nm
* Auxiliary drive belt tensioner to engine 22 Nm
* Starter motor to flywheel housing bolts 37 Nm
* Starter solenoid terminal nuts 4 Nm
* Horn mounting bracket to body 9 Nm
* Horn to mounting bracket 10 Nm

* INSTRUMENTS
* Oil temperature gauge sensor 60 Nm

* RESTRAINT SYSTEMS
* Rotary coupler bolts 15 Nm
* Diagnostic unit 9 Nm
* Airbag module screws 7 Nm
* Diagnostic harness earth lead bolt 10 Nm
* Front seat belt stalk bolt 32 Nm
* Front seat belt upper mounting bolt 32 Nm
* Front seat belt lower mounting bolt 30 Nm
* Front seat belt upper mounting bolt 30 Nm
* Seat belt pre-tensioner reel bolt 30 Nm
* Seat belt pre-tensioner tube nut 6 Nm
* Seat belt pre-tensioner tube screw 1.2 Nm
* Rear seat belt buckle to body - bolt 30 Nm
* Rear seat belt reel to body - bolt 30 Nm
* Rear seat belt lower mounting bolt 30 Nm
* Rear seat belt upper mounting bolt 30 Nm

* BODY
* Bonnet hinge nuts 9 Nm
* Front/Rear bumper to body - nuts 10 Nm
* Door striker to body - screws 18 Nm
* Bonnet latch to body - bolts 9 Nm
* Wheel arch extension to body - nuts 9 Nm
* Fascia top rail to body - nuts 9 Nm
* Front seat to body - nut and bolt 25 Nm

* HEATING AND VENTILATION
* Heater to bulkhead - nut 9 Nm

* WIPERS AND WASHERS
* Wiper wheel boxes to body - nut 10 Nm

engine, see also